How to Drain Your Water Heater: A Step-by-Step Guide

Tank water heaters are a reliable way to provide a fast supply of hot water for your home. The inclusion of a storage tank ensures some hot water is always available. But over time, other substances can build up in the storage tank. This might be sediment or mineral buildup arriving from the main water line or a crack in the pipes. Whatever the source is, this buildup could lower the efficiency of water heaters. In severe cases it can clog up drainage and may even cause premature failure.

Thankfully, draining your water heater and removing sediment buildup is a relatively simple task. An experienced plumber in Columbia can handle the process, but you can also drain the tank yourself if you know what you’re doing. Whatever you choose, draining the tank now can help lower the risk you’ll need premature water heater replacement.

Before You Begin…

Before you start draining the tank, you should shut off the cold water supply. The supply valve connects your water heater with the main water line. Unless you have access to a well (and you might need to drain the tank more frequently if you do), the water main delivers all the potable water your home uses. Keeping the valve shut will prevent more water from flowing into the tank, allowing you to completely drain it.

You’ll also want to get a rubber hose, like one you could use for yard work. The hose allows you to safely drain the water heater tank without spilling water in your garage, utility closet, attic or wherever the water heater is kept. Make sure you leave the other end of the hose far away from your home to prevent the water from seeping back inside.

Finally, a screwdriver should help you loosen tight screws or valves. You shouldn’t need any more tools than this unless you come across a problem with the water heater or adjacent piping. At that point, it might be best to contact a certified plumber in Columbia.

Step 1: Shut Off the Water Heater

After you’ve cut off the water supply, you can shut off the water heater itself. This should be on the thermostat for natural gas water heaters or via a breaker switch for electric models. The pilot setting on gas water heaters can remain on during flushing, but electric models must be completely off. This is due to the heating elements electric water heaters use, which remain submerged. In an empty tank, they could quickly overheat. You should also check the model’s manual, as some water heaters must be completely full before the heating elements are turned on.

Even after you’ve shut off the water heater, you’ll have to wait for the water stored in the tank to cool down. It may be hours before the water reaches a safe temperature, so it may be best to leave the remaining steps for the following day.

Step 2: Connect the Hose to the Water Heater’s Drain Valve

Tank water heaters are designed with a drain valve you can use to empty the storage tank. Once you’re sure the water supply is disconnected and the water heater itself is off, go ahead and find the drain valve. Some models may have it covered up. Make sure the hose is securely fastened to prevent spilling hot water near you and the water heater.

Step 3: Open a Faucet or Other Hot Water Tap

Your home’s plumbing uses pressure within the piping to deliver a consistent flow of water from the main water line to the rest of the house. This pressure needs to be relieved before the hot water can actually exit the tank. By heading to the nearest faucet or spigot, you’ll alleviate the pressure inside the piping. All you have to do is open the hot water tap to relieve the pressure before returning to the water heater.

Step 4: Release the Drain Valve

Remember that this water might still have some residual heat. Open the drain valve and allow all the water to drain from the tank. This should carry sediment buildup out of the tank and away from your home. But some buildup may be stuck to the inside of the tank. Turning the cold water supply back on will help flush stubborn minerals and other substances from the tank.

Keep repeating this step until the water appears clear of sediment or minerals. If the drain isn’t working because of an obstruction, a trained plumber is likely required.

Step 5: Re-Shut the Valve Before Refilling the Water Heater

If everything proceeds normally, you should be able to remove most excess sediment hiding inside your water heater. Close the drain valve, disconnect the hose and open the water supply to get things flowing again. As the water heater tank begins to fill, head back to the hot water tap you opened. Once cold water starts to flow, you know the pressure is back where it needs to be.

At this point, you can open the gas valve or flip the breaker switch back on. Like we mentioned earlier, don’t forget that certain models might need to be completely full before the water can be safely heated. Make sure you review your manufacturer’s instructions before starting the process.

Keep Your Water Heater Sediment-Free for Best Results

Tank water heaters continue to be a great option for supplying your hot water needs. Draining the tank every 1-2 years will help remove sediment buildup and keep things running at peak efficiency. If you think your water heater is past the point of efficient heating, consider looking for water heater replacement in Columbia from a technician you trust.